Centos 6 Igb Driver
Question: I want to build and install the latest ixgbe 10G NIC driver. How can I compile ixgbe driver on CentOS, Fedora or RHEL? To use Intel's PCI Express 10G NICs (e.g., 82598, 82599, x540) on your Linux system, you need to install ixgbe driver. While modern Linux distributions come with ixgbe driver pre-installed as a loadable module, the pre-built ixgbe driver is not fully customizable with limited parameters. If you want to enable and customize all available features of the 10G NICs (e.g., RSS, multi-queue, virtual functions, hardware offload), you will need to build the driver from the source. Here is how to compile ixgbe driver from the source on Red Hat based platforms (e.g., CentOS, RHEL or Fedora). For Debian based systems, refer to instead.
Step One: Install Prerequisites First, set up necessary development environment and install matching kernel headers. $ dmesg Intel(R) 10 Gigabit PCI Express Network Driver - version 3.23.2 Copyright (c) 1999-2014 Intel Corporation. It looks like KernelCare is guilty for crash, don't know what else. Switched back to Ksplice. Tried using DKMS, but it looks like there is some clash since I've already have up and running module following your instructions on this page.
root@main # dkms status ixgbe, 4.3.15, 3.10.0-327.10.1.el7.x8664, x8664: built root@main # dkms install -m ixgbe -v 4.3.15 ixgbe: Running module version sanity check. Original module - Multiple original modules exist but DKMS does not know which to pick - Due to the confusion, none will be considered during a later uninstall - Multiple same named modules!
Article ID: 000005767 Using the Linux igb. base driver for Intel® Gigabit Ethernet network Connections The igb driver supports all 82575, 82576, 82580, and I350-based Intel® Gigabit Ethernet Network Connections.
Using the igb base driver. For information concerning driver configuration details, please refer to the README file located at the download link above. Overview The Linux base drivers support the 2.4.x, 2.6.x and 3.x kernels. These drivers includes support for Itanium® 2-based systems.
These drivers are only supported as a loadable module. Intel is not supplying patches against the kernel source to allow for static linking of the drivers. For questions related to hardware requirements, refer to the documentation supplied with your Intel Gigabit adapter. All hardware requirements listed apply to use with Linux.
The following features are now available in supported kernels:. Native VLANs.
Channel Bonding (teaming). SNMP Channel Bonding documentation can be found in the Linux kernel source: /documentation/networking/bonding.txt The igb driver supports IEEE 1588 time stamping for kernels 2.6.30 and above. A basic tutorial for the technology can be found on the web site. The driver information previously displayed in the /proc file system is not supported in this release. Alternatively, you can use ethtool (version 1.6 or later), lspci, and ifconfig to obtain the same information.
Instructions on updating ethtool can be found in the section later in this document. Building and installation To build a binary RPM. package of this driver, run 'rpmbuild -tb igb.tar.gz'. Note. For the build to work properly, the currently running kernel MUST match the version and configuration of the installed kernel sources. If you have just recompiled the kernel reboot the system now.
Centos 6 32 Bit
RPM functionality has only been tested in Red Hat distributions. Move the base driver tar file to the directory of your choice.
Download Igb
For example, use '/home/username/igb' or '/usr/local/src/igb'. Untar/unzip the archive, where is the version number for the driver tar file: tar zxf igb.tar.gz. Change to the driver src directory, where is the version number for the driver tar: cd igb-/src/. Compile the driver module: make install The binary will be installed as: /lib/modules//kernel/drivers/net/igb/igb.ko The install location listed above is the default location. This may differ for various Linux distributions. Load the module using either the insmod or modprobe command: modprobe igb insmod igb Note that for 2.6 kernels the insmod command can be used if the full path to the driver module is specified. For example: insmod /lib/modules//kernel/drivers/net/igb/igb.ko With 2.6 based kernels also make sure that older igb drivers are removed from the kernel, before loading the new module: rmmod igb; modprobe igb.
Assign an IP address to the interface by entering the following, where is the interface number: ifconfig eth. Verify that the interface works.
Additional delivery time may result for some deliveries. Please allow extra time for delivery to western states. Protek 506 service manual. Premium freight is not available on oversized or bulky items. Delivery Charges: Up to $99.99 $9.00 $100 - $199.99 $11.00 $200 - $499.99 $16.00 $500+ $23.00 *Freight delivery times stated are for average volume items with total order weight under 5kg for metro areas in eastern states.
Enter the following, where is the IP address for another machine on the same subnet as the interface that is being tested: ping Note Some systems have trouble supporting MSI and/or MSI-X interrupts. If you believe your system needs to disable this style of interrupt, the driver can be built and installed with the command: # make CFLAGSEXTRA=-DDISABLEPCIMSI install Normally the driver will generate an interrupt every two seconds, so if you can see that you're no longer getting interrupts in cat /proc/interrupts for the ethX igb device, then this workaround may be necessary. To build igb driver with DCA: If your kernel supports DCA, the driver will build by default with DCA enabled.